👉 🔥 CLICK HERE! 🔥 👈

The company does not work correctly if cookies are disabled. To avoid possible damage, remove the battery if the device is not used. 2. Keep the controller away from excess heat or moisture. 3. This remote control unit is required with 24 -bit code combinations. To prevent possible disorders or other long resolution devices, such as garage door holes, car alarm or safety system. If it turns out that your fan and light set will continue and the control will not be used, just change the connected code in the transmitter and receiver. 4. Track tile working wrench. High key - for maximum fan speed. Medical key - fan for average speed. Low -KEY - for lower fan speed. Deactivate - to turn off the fan speed. Rev key - reverse fan speed. Control switch - for light brightness IODfrom control. 5. Start the fan: Press the speed button you want to start for the fan. 6. Turn off the fan: Press the Disable button. 7. Light control: Turn off the light or turn off only by touching the light control button. Then press the button over 0.7 seconds, it is expanded, the light changes periodically within 0.8 seconds. One of the most important features of this control is an automatic resident. If the power supply is turned on, the light can return where it has been turned off. General information: This pilot has been designed in such a way as to separate the ceiling fan speed and light brightness. The Light 910805 key controls the brightness of light onoff. The LED display on the transmitter is lit up after pressing the button. Installation and operation of the fan speed control 1. Determining the code in the new station. Press the buttonstop in 60 seconds. Then the recipient captures the frequency of the selected frequency. IfThe store will not work properly if cookies are turned off. To prevent possible damage, remove the battery when the device is not in use. 2. Keep the controller away from excessive heat or moisture. 3. This remote control unit is required with a combination of 24 -TOS. To avoid possible interference or other remote devices such as garage doors, car alarm or security system. If you find that your fan and light set continue and dont use the controller, simply change the combined code in the transmitter and receiver. 4. The transmitters operating buttons. High key - for maximum fan speed. Honey key - average speed fan. Low -Key - For lower fan speed. Disable button - Turn off the fan speed. REV key - fan speed. Control Switch - for bright brightness and onoff control. 5. Start the fan: Press the Speed button to turn on the fan. 6. Turn off the fan: Press the Shut -OFF button. 7. Light Control: Turn on or off just by touching the light control button. Next, press any button more than 0.7 seconds, the light will change cyclically in 0.8 seconds. One of the most important features of this controller is an automatic resident. When the power is on, it allows the light to return where it was turned off. General Information: This remote control is designed to separate your ceiling fan speed and light brightness separately. The 910805 light button controls brightness onoff. The LED on the transmitter lights up when the button is pressed. Fan Speed Installation and Operation Instructions 1. Determine the code in the new transmitter. Press the shutdownstop button within 60 seconds. The receiver then acquires the frequency of the selected frequency. IfThe fan has an indicator, blink twice, and fans without light check the operation using the transmitter note. Changes or modifications that have not specifically confirmed the responsible party may eliminate the users right to use equipment. This unit corresponds to paragraph 15 of the FCC Rules. The following two conditions apply: (1) This unit cannot cause harmful interference and (2) This unit must accept any incoming disturbances, including interference that can cause unwanted acts. This unit corresponds to the Licensed Industry Canada RSS standard (s). The following two conditions are valid: (1) This unit cannot cause interference and (2) This unit must accept any interference, including interference that can cause unwanted operation of the unit. The Presenta device corresponds to the EN Industry Canada CNR applied to the AUX radio license. Acting is allowed in the following two conditions: (1) the applied non-baptism must not form, and (2) the calling user must accept any radial three, experienced, even if it has been incurred by radial interference = document description 00: 00: 00: 29: 47Producing Softwaregpl Ghostscript 8.15Document Lastmod2014-05-26 00: 43: 28 Document Name Lietotāju Rokgrāmata.dll.document Facher. Type: PDF File Type Extension: PDF MIME Type: ProgramPDF PDF Version: 1.4 Linear: without tools XMP: Adobe XMP CORE 5.4-C005 78.147326, 20120823-13: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03: 03:: | : 26 00: 43: 28+08: 00 Manufacturer: GPL Ghostscript 8.15 Document ID: UUID: ACC2191F-092E-47D9-909B-42A21F072F76 Case ID: UUID: C18CF8C8B8D3: 254 Userdb8 is not included). To prevent possible damage due to the battery, be sure to remove the battery when you do not use the device. This unit has one of the black lines with AC 120V. The color of the ground conductor is Kelly. Keep the controller out of excessive heat or moisture. This remote control is required when using 24 -bit codes combinations. To avoid potential interference with other remote devices such as garage door openers, car alarms or safety systems. If you find that the fan and the light set are switched on and off without the use of the control panel, simply change the combination code of the transmitter and receiver. Control buttons on the transmitter panel. Fan high -speed key. button- to control the average fan speed. button - to control low fan speed. button- to control the fan speed OFF. OR or - to control the brightness and onoff the light. button - reverse fan speed. Power switch - onoff the fan start: Press the fan button to start the fan to the desired level. Turn off the fan: Press the OFF button. Press and hold the button for more than 0.7 seconds, mutes, the light is cyclically mutes in 0.8 seconds. One of the important functions of this command is automatic recovery. After the power is switched on, the light allows the light to return where it has been turned off. General

Items