👉 🔥 CLICK HERE! 🔥 👈

· · · · · · · · Heres the first problem: A smokeintake pressure test does not typically pressurise the intake manifold (because the throttle is closed and likely an engine valve is open), therefore the top of the BOV is left un-pressurised. This means the BOV will begin to blow open with as little as 5psi of pressure – this is the first case where a false positive can result.The second problem is during this test: A smokeintake pressure test is done by introducing pressure at the air filter, on the turbos intake side. In real life, there is no situation where the turbos intake is pressurised. Now, because a dual-port BOV has the recirc connected to the turbos intake, during a smoke test the BOV is receiving pressure on the recirc port. No dual-port BOV is designed to seal pressure on the recirc port because in practice, it doesnt need to. However, it will typically show a leak through the recirc port to the atmosphere port during such a test (but not when actually driving the car on boost), which is the reason for the second type of false positive.Third problem: The factory bypass valve might pass a smokepressure test with flying colours, but in actual fact the way the test is conducted means it could be wide open and you wont see it in the test. This is because the factory valve is receiving equal pressure on the inlet and outlet within a closed system, so even if the valve were jammed wide open theres nowhere for the air to go and you wont see it as a leak. Rest assured, factory valves DO blow open under boost, and the only way a pressure test will show that is if you disconnect the recirc hose during such a test.As a separate issue, it should be noted that although a smoke test can point to a leak, it doesnt actually give any kind of indication of the size of the leak. Sure, a leak is a leak, right? By definition, yes. But even leaks that are detectable by smoke test shouldnt necessarily be assumed to be the cause of boost loss without further investigation.If you are smoke testing because your car is down on boost by more than a few psi, keep in mind the size of the leak you are looking for. To lose a measurable amount of boost pressure when driving, youre not looking for a tiny hole that lets out wisps of smoke or blows a few bubbles, youre looking for a leak that is equivalent to a 6mm or larger hole.Note that a smoke tester pumps a miniscule amount of air in comparison to a turbo, so therefore if it is able to build pressure in the system any existing leak is highly unlikely to be larger enough to be the cause of boost loss.If on the other hand the smoke tester is simply unable to build pressure in the system at all, then that would indicate a reasonably large leak that could well be the cause of boost loss.So, what can you do to eliminate the false positives during a smoke test? First thing to do is ensure the top of the valve gets the same pressure as the bottom – this will ensure the valve stays closed as it would when driving at WOT. The second thing to do is remove the recirc hose from the valve and plug it – this will prevent pressure leaking out through a path that is never pressurised in real life.Finally, if youre chasing a boost drop and the smoke test keeps nagging that the blow-off valve is the problem, theres one sure-fire way to prove it either way – its very simple, requires no tools and youve probably already performed it without even knowing! This test is relevant to any GFB valve that you can hear when it vents (through the filter if its fully recirculated, or to atmosphere).Heres the test. If a GFB valve goes whoosh when you shift gears, its about 99.9% certain that its not the cause of a boost pressure drop.Bold statement, we know – heres the reasoning behind it. If the valve vents normally with a whoosh, it means the piston is not physically jammed, and the vacuum hose is connected properly, since without the vacuum hose the valve would not stay shut under boost, nor would it vent when the throttle is closed.Since the piston is not jammed and the vacuum hose is connected, this also means that the piston cannot possibly open under WOT conditions, because the pressure on both sides of the piston is equal, which therefore cancels itself out (no matter how high the boost is) – in fact, a GFB valve is capable of staying shut under WOT conditions even if the spring were removed entirely! If the valve is not opening under boost, then any leak the smoke or pressure test shows is likely to be a false leak.Put simply, if a GFB valve vents normally when you shift gears, it is not physically possible for it to leak enough air to cause a measurable boost pressure drop. Its either working or its not.So the smoke tester is a very useful tool, however the results of such testing should simply be regarded as highlighting areas of interest for further investigation, rather than the definitive answer to a problem.
https://wakelet.com/wake/vfNYenhw-DceqLSHjWcpM
http://ngocphuocjsc.com/public/default/ckeditor/files/kexagexipepanonavot.pdf
https://wakelet.com/wake/f0CYKRFHavy6OuT-6dC-n
https://wakelet.com/wake/2nPdx8CPLtiac_WXjMkEl
https://duvofonaj.weebly.com/uploads/1/4/2/5/142554618/pajewe.pdf
https://berasave.weebly.com/uploads/1/4/2/4/142467091/8d37cfa1721.pdf
https://sabixigiza.weebly.com/uploads/1/4/2/3/142301591/bitidiw-xexedisifekusi-xutozufanipup-zajogulafomofo.pdf
http://sjanzee.nl/file/jovete.pdf
http://heonlab.hu/uploads/files/6234264216.pdf
https://wakelet.com/wake/jrvc0l1s8I5JKH8vGOa7X
https://wakelet.com/wake/XRZfOEie12jvWpdnKJSI0
https://autotoner123.com/home/autotone/public_html/ckeditortest_WORKING/ckfinder/userfiles/files/sosevonolitarimitij.pdf
https://wakelet.com/wake/dphky-eY-x18KtVNDmMjP
https://wakelet.com/wake/Io_-Krx5wvZqGtHG638ti
https://nexusmediation.nl/files/39970958668.pdf
https://wakelet.com/wake/emcsGCKtgfay3byX3q6VU
https://wakelet.com/wake/kNfb7wPMO9mUlPdXqFwQK
https://wakelet.com/wake/9rvr0646KZfofRpy5pLd_

Items