Henon Map  Crack+ Activator (Latest)
LAMBDA
HenonMap.Lambda (LINEARITY)
Linearity: Specify the amount of linearity to add to the Henon Map Cracked Accounts equation.
0.0 Linearity: no linearity
0.5 Linearity: linear from octave to octave
1.0 Linearity: linear from semitone to semitone
There is no point in adding more linearity than there is in the source, it will just be overkill and make things muddier.
SIN
HenonMap.Sin (SINUSITY)
Sinusity: Specify the amount of sinusarity to add to the Henon Map Full Crack equation.
0.0 Sinusity: no sinusarity
0.5 Sinusarity: sinusarity only from the current semitone to the next one
1.0 Sinusarity: sinusarity from source
There is no point in adding more sinusarity than there is in the source, it will just be overkill and make things muddier.
EXP
HenonMap.Exp (EXPONENTIALITY)
Exponentiality: Specify the amount of exponentiality to add to the Henon Map Activation Code equation.
0.0 Exponentiality: no exponentiality
0.5 Exponentiality: exponential from the current semitone to the next one
1.0 Exponentiality: exponential from source
There is no point in adding more exponentiality than there is in the source, it will just be overkill and make things muddier.
New Wave Form: Gate One (Extreme Feedback, A.Slow, Var.High)
New Wave Form: Gate Two (No Feedback, Extreme Tones, Var.Low)
New Wave Form: Gate Three (Clean)
New Wave Form: Gate Four (Minimalistic Waveform)
Add as many modules as you want in the modules/waveform folder.
New Wave Form - Gate One
Although Gate One is fairly typical it is great for accenting the 2nd harmonic in isolation (we can get even better results with the Shake filter, check out the De-tune module).
Let’s go for a very extreme circular wave form, Gate One
1 | Gate One Filter | Frequency $$ 36° | Time Length $$
Henon Map  Crack + License Key Free X64
The Henon Map Crack Module is designed to be used with the MZX1 Harmonic Synthesizer. The basic algorithm was designed to imitate the behavior of a cathode ray tube (CRT) oscilloscope by flashing thru periodic ranges of window. This results in a large range of sounds and a wide variety of strange sound effects. The module allows the circuit to be preset to a specific sound and then used as a note or gate circuit. Note that sound will only occur when the Gate is open.
Here is a brief description of how it works:
1. The Synth
2. The Module
3. Installing the Module
1. The Synth
The MZX1 has a built in oscilloscope. The oscilloscope can be accessed via User Select Module (1A) and it consists of a range of analog horizontal/vertical traces. All of the traces are capable of being turned off. They can all be individually turned on to different degrees and all of them can also be turned off completely. If a trace is off then nothing will be heard when this trace is selected as the note. To select a trace, select a range of traces (i.e., the left end of the range will be at the left most trace and the right end of the range will be at the right most trace). The range of traces is selected to be one of the following:
The parameter windows should be set to meet your needs (see the screenshots). For note selection: the window can be turned on and off and the amplitude may be adjusted. Most of the controls are self explanatory (see screenshot).
Here is a wiring diagram for the module (click on the image to enlarge):
The windows and their functions are as follows:
Window 1:
This is the note selection or gate timing window. It cycles thru the range of traces (i.e., the left trace in the range will be selected last) and plays a sound when the trace is selected.
Window 2:
This is the oscilloscope slider. The range of the slider is from the left most trace on the first range of traces (i.e., the left most trace will be 1 the right most trace will be 45) to the right most trace on the last range of traces (i.e., the right most trace will be 45). The value is 1/4 of the selected amount. I.e., if the range is set to 3, then the
f0d5c1b395

Related

Items